🌐 Manual · Chapter 1

DMX output:
connecting MyStrow to your lights

For MyStrow to drive real fixtures, it needs a DMX interface between the computer and the first fixture. This chapter covers everything in Connection › 🌐 DMX Output and the test tools.

By MyStrow·Updated 18 November 2026

The principle: computer → interface → fixtures

A computer doesn't output DMX on its own. You plug in an interface:

  • over USB: a USB-DMX box (ENTTEC, Eurolite, Open DMX…);
  • over the network: an Art-Net node connected by Ethernet (RJ45), directly or through a switch.

From the interface, a DMX (XLR) cable runs to the first fixture, then from fixture to fixture. One DMX line = one universe = 512 channels. MyStrow handles up to 4 universes.

During the 15-day trial, DMX output works. After the trial, it requires an active license.

Opening the DMX Output window

Menu Connection › 🌐 DMX Output. The window starts by asking which interface you have, with three choices you can tell apart by where the yellow logo is:

  • MyStrow logo on the front: this is the USB NODE DMX (ElectroConcept), the box in the MyStrow Pack. It plugs in over USB but speaks Art-Net: MyStrow sets it up on its own in the Node output, with no IP address to touch.
  • MyStrow logo on top: this is the MyStrow USB-DMX (MS-DMY). Plug it in over USB, MyStrow finds it on its own. If you've just plugged it in, click 🔌 Connect.
  • Other interface: the full screen, with two tabs, 🌐 Node output and 🔌 USB DMX output.

USB-DMX interface (USB DMX output tab)

  1. Plug the interface in over USB (preferably directly into the computer, without a hub).
  2. In Interface, choose your model: MyStrow USB-DMX (MS-DMY), Eurolite USB-DMX512 PRO (MK2), ENTTEC DMX USB Pro, ENTTEC Open DMX USB, OPTO OPEN DMX (ElectroConcept), DMXKing UltraDMX Micro, or Other USB-DMX interface.
  3. Choose the COM port that appears when the interface is plugged in.
  4. Click 🔌 Connect. On most interfaces, an LED turns green when DMX output is active.

Does your box say Art-Net, Node or RDM? Even if it plugs in over USB, it isn't set up here: use the Node output tab. That's the case for the USB NODE DMX.

“Port unavailable”: another program (QLC+, Freestyler, Chataigne…) is using the interface. Close it: only one program at a time can use it.

A USB interface carries only one universe. Plugging in several USB interfaces doesn't give you several universes: for that, you need Art-Net nodes.

For an Open DMX or an FTDI-chip interface, install the FTDI driver if MyStrow offers it.

Art-Net node (Node output tab)

  1. Connect the node to the computer with an Ethernet cable (avoid Wi-Fi for DMX).
  2. Under Network card, check the card connected to the node.
  3. Under Art-Net node, pick your node from the devices that answered, or type its IP address. Search the network again repeats the detection.
  4. Click 🔌 Connect.

The network must be in the same range as the node. Many Art-Net nodes use 2.x.x.x (ElectroConcept boxes ship set to 2.0.0.15), others 192.168.x.x. The ⚙️ Set up the network connection button starts a wizard that:

  • asks you to choose the network card connected to the box (not the Wi-Fi);
  • sets the computer to 2.0.0.1 / mask 255.0.0.0, either automatically (requires administrator rights: 🔑 Restart as administrator) or by hand with I'll configure it myself, which shows the Windows steps;
  • tests the connection and confirms that the box is connected.

If MyStrow finds the box at a different address from the one it's looking for, it says so and offers a Use [address] button: one click is enough, nothing to change on the network.

On first launch, allow MyStrow through the firewall when Windows asks: otherwise the node won't be found.

Several universes and several nodes

In the Node output tab, Advanced options › Output routing shows, for each DMX line, which universe goes out on it and to which node.

  • Node with 2 or 4 outputs: one box is enough, each output carries its universe.
  • Several 1-output nodes: give each node its own IP address and Art-Net universe (with the manufacturer's utility), then pick the right node on each row of the table.
  • Two lines can carry the same universe: that's mirroring, to duplicate a line at the other end of the venue without a splitter.
  • A line can be Disabled or used as a DMX input (console), to drive MyStrow from a lighting desk.

Then, in the patch, put each fixture in the universe of the line it's cabled on (addresses restart at 1 in each universe). Full walkthrough: several universes with several Art-Net nodes.

Testing the output: DMX Tester and DMX Monitor

Edit › 🔬 DMX Tester sends values directly to channels, bypassing the patch. It's the tool to find out whether a fixture receives DMX:

  • choose the DMX universe, click and drag on channels to set their value (Ctrl = several channels, Shift = a range, mouse wheel = ±5);
  • buttons raise or lower all 512 channels at once;
  • GROUP TEST lights channels in packs (set Channels per group, then ▶▶ Send the next ones) to find a fixture's address;
  • the MIDI controller's faders drive 9 channels at a time;
  • when you close it, the show is restored as it was.

Edit › 📡 DMX Monitor shows live what actually goes out on each universe: active channels, frames per second, interface used, and a warning if a universe isn't being sent (for example universe 2 on a USB interface, which only carries universe 1).

Diagnosing a silent output

Menu Connection › 🩺 Diagnostics:

  • 🌐 RJ45 test (network / Art-Net Node): checks cable, network card, IP address and the box's response, and offers to fix what's wrong;
  • 🔌 USB test (DMX interface): checks the USB interface and its port;
  • 🩺 Full diagnostic (BRAD): runs all the Art-Net output tests. 📋 Copy the report or ✉️ Send to support sends us the result.

The most frequent causes, in order:

  1. another lighting program open, using the interface;
  2. a USB Art-Net interface (USB NODE) looked for in the USB tab instead of the Node output;
  3. computer and node not in the same IP range, or a firewall blocking;
  4. the fixture isn't at the address or in the DMX mode of the patch (DMX goes out, but the fixture listens elsewhere): the DMX Tester reveals it straight away;
  5. faulty USB cable, port or DMX cable.

On Mac, if the output stayed on “USB” while you're using a node, reopen DMX Output and choose Art-Net.

Which DMX interface should I buy for MyStrow?

Any USB-DMX interface or Art-Net node on the market works. The simplest is the MyStrow Pack (interface + license): MyStrow recognises and sets it up on its own. For more than one universe, get an Art-Net node.

How many fixtures can I control?

A universe is 512 channels, and MyStrow handles up to 4 universes (2,048 channels). The number of fixtures depends on each one's channel count: a 7-channel PAR takes 7, a 16-channel moving head takes 16.

Is Wi-Fi enough for an Art-Net node?

It's possible but not recommended: Wi-Fi adds dropouts and latency. Connect the node with an Ethernet cable, directly or through a switch.

My interface is detected but nothing lights up.

Open Edit › 🔬 DMX Tester and raise the fixture's channels. If it lights, the output works: the patch address or DMX mode doesn't match the fixture. If it stays dark, check the DMX cable and run Connection › 🩺 Diagnostics.